联系我们
名称：徐州通风管道诚信加工厂
电话：xxx
手机：xxx
邮箱：xxx
地址：xxx
新闻动态
正确维护水泥垫块机的方法是什么
正确维护水泥垫块机的方法是什么
What is the right way to maintain the cement block machine
1、在运转正常后方可加料，同时喂料要均匀，应防止混入铁块硬物。
1. The feeding can only be carried out after the normal operation, and the feeding shall be uniform to prevent mixing with hard iron.
2、在检查紧固件是否松动时，应重点检查转子两侧压紧板锤的压板螺钉。
2. When checking whether the fasteners are loose, the pressing plate screws of the pressing plate hammers on both sides of the rotor shall be mainly checked.
3、在停机前必须先停止加料，停机内物料破碎完毕再停电动机。
3. The feeding must be stopped before the shutdown, and the motor shall be stopped after the materials are broken in the shutdown.
4、防止压板松动后，板锤两端露出转子体，与机体碰击，损伤机件。
4. After the pressing plate is loose, the two ends of the plate hammer will expose the rotor body, collide with the body and damage the parts.
5、当板锤因磨损需调整180°再次使用时，应使每块板锤重量相等并保持平衡，以防止反击破开动后发生震动。
5. When the plate hammer needs to be adjusted 180 ° for reuse due to wear, the weight of each plate hammer shall be equal and balanced to prevent vibration after the impact breaking.
6、当水泥垫块机产品粒度过大时，应停机检查板锤磨损情况，防止转子被磨坏。
6. When the particle size of the cement block machine is too large, stop the machine to check the abrasion of the plate hammer to prevent the rotor from being worn out.
7、水泥垫块机在检修或调整排料口后，应先用人力转动转子，确认转子与其他零件没有摩擦和卡住现象并能灵活转动。
7. After repairing or adjusting the discharge port, the cement block machine shall first rotate the rotor by manpower to make sure that there is no friction and jamming between the rotor and other parts and that it can rotate flexibly.
8、应经常检查轴承座密封是否良好，轴承座内润滑脂应每月加注一次，每三个月应全部清洗换油及更换油毛毡。
8. Check whether the seal of bearing seat is in good condition. Fill lubricating grease in bearing seat once a month. Clean and change oil and felt every three months.
What is the right way to maintain the cement block machine
1、在运转正常后方可加料，同时喂料要均匀，应防止混入铁块硬物。
1. The feeding can only be carried out after the normal operation, and the feeding shall be uniform to prevent mixing with hard iron.
2、在检查紧固件是否松动时，应重点检查转子两侧压紧板锤的压板螺钉。
2. When checking whether the fasteners are loose, the pressing plate screws of the pressing plate hammers on both sides of the rotor shall be mainly checked.
3、在停机前必须先停止加料，停机内物料破碎完毕再停电动机。
3. The feeding must be stopped before the shutdown, and the motor shall be stopped after the materials are broken in the shutdown.
4、防止压板松动后，板锤两端露出转子体，与机体碰击，损伤机件。
4. After the pressing plate is loose, the two ends of the plate hammer will expose the rotor body, collide with the body and damage the parts.
5、当板锤因磨损需调整180°再次使用时，应使每块板锤重量相等并保持平衡，以防止反击破开动后发生震动。
5. When the plate hammer needs to be adjusted 180 ° for reuse due to wear, the weight of each plate hammer shall be equal and balanced to prevent vibration after the impact breaking.
6、当水泥垫块机产品粒度过大时，应停机检查板锤磨损情况，防止转子被磨坏。
6. When the particle size of the cement block machine is too large, stop the machine to check the abrasion of the plate hammer to prevent the rotor from being worn out.
7、水泥垫块机在检修或调整排料口后，应先用人力转动转子，确认转子与其他零件没有摩擦和卡住现象并能灵活转动。
7. After repairing or adjusting the discharge port, the cement block machine shall first rotate the rotor by manpower to make sure that there is no friction and jamming between the rotor and other parts and that it can rotate flexibly.
8、应经常检查轴承座密封是否良好，轴承座内润滑脂应每月加注一次，每三个月应全部清洗换油及更换油毛毡。
8. Check whether the seal of bearing seat is in good condition. Fill lubricating grease in bearing seat once a month. Clean and change oil and felt every three months.
