联系我们
名称：徐州通风管道诚信加工厂
电话：xxx
手机：xxx
邮箱：xxx
地址：xxx
新闻动态
压浆料施工要点
压浆料施工要点
Key Points of Grouting Material Construction
水料比为0.26~0.28，可根据灌浆部位不同进行调整。
The ratio of water to material is 0.26~0.28, which can be adjusted according to different grouting positions.
首先在搅拌机中加入实际拌合水的80%-90%，开动搅拌机，均匀加入全部压浆料，边加入边搅拌。全部粉料加入完毕，然后快速搅拌3min，加入剩下的10%-20%的拌合水，继续搅拌2min。
Firstly, 80% to 90% of the actual mixing water is added to the mixer, and the mixer is started, and all the mortar is evenly added, while mixing. After adding all the powder, stir quickly for 3 minutes, add the remaining 10% - 20% water, and continue stirring for 2 minutes.
压浆料自搅拌至压入孔道的延续时间，视气温情况而定，一般在30~1h范围内。
The duration of the grouting material from stirring to pressing into the channel depends on the temperature, generally within the range of 30 to 1 h.
压浆料在使用前和压注过程中应连续搅拌，以维持浆体的均匀性和流动性。
The grout should be stirred continuously before use and during the process of grouting to maintain the homogeneity and fluidity of the slurry.
压浆时应使用活塞式压力泵或真空泵，压力需大于0.7MPa。
Piston pressure pump or vacuum pump should be used when grouting. The pressure should be greater than 0.7 MPa.
压浆时浆体温度应保持在5℃-30℃之间，否则应采取措施满足条件。
When grouting, the slurry temperature should be maintained between 5 and 30 degrees Celsius, otherwise measures should be taken to meet the conditions.
Key Points of Grouting Material Construction
水料比为0.26~0.28，可根据灌浆部位不同进行调整。
The ratio of water to material is 0.26~0.28, which can be adjusted according to different grouting positions.
首先在搅拌机中加入实际拌合水的80%-90%，开动搅拌机，均匀加入全部压浆料，边加入边搅拌。全部粉料加入完毕，然后快速搅拌3min，加入剩下的10%-20%的拌合水，继续搅拌2min。
Firstly, 80% to 90% of the actual mixing water is added to the mixer, and the mixer is started, and all the mortar is evenly added, while mixing. After adding all the powder, stir quickly for 3 minutes, add the remaining 10% - 20% water, and continue stirring for 2 minutes.
压浆料自搅拌至压入孔道的延续时间，视气温情况而定，一般在30~1h范围内。
The duration of the grouting material from stirring to pressing into the channel depends on the temperature, generally within the range of 30 to 1 h.
压浆料在使用前和压注过程中应连续搅拌，以维持浆体的均匀性和流动性。
The grout should be stirred continuously before use and during the process of grouting to maintain the homogeneity and fluidity of the slurry.
压浆时应使用活塞式压力泵或真空泵，压力需大于0.7MPa。
Piston pressure pump or vacuum pump should be used when grouting. The pressure should be greater than 0.7 MPa.
压浆时浆体温度应保持在5℃-30℃之间，否则应采取措施满足条件。
When grouting, the slurry temperature should be maintained between 5 and 30 degrees Celsius, otherwise measures should be taken to meet the conditions.
